# Equations (not in formula sheet)
- $\tau=\mu \frac{\partial u}{\partial y}$ where $y$ is perpendicular to the direction of flow
- $dF=\tau dA$
- $\dot{m}_{in}=\dot{m}_{out}\to \rho_{1} Q_{in}=\rho_{2} Q_{out}$ where volumetric flow rate $Q=\int udA$
- If cross-sectional area is not normal to the velocity vector, $Q=\int_{A}u\cos\theta dA$
- $\bar{u}=\frac{Q}{A}$
- $Q=\frac{\dot{m}}{\rho}$
# Notes
- It's often smart to find an equation for the final quantity and find the required values for that first.
- If you use gauge pressure, atmospheric pressure is defined as zero
- Be careful of what units you choose for $\rho$ in US/English
- For $\int_{CS}\vec{v}_{x}(\rho \vec{V}_{xyz}\cdot d\vec{A}),$ $v_{x}\neq V_{xyz}$
> [!info] Application of the Energy Equation
> The way we normally treat the energy equation is through simplifications. In this course, most of the time we will deal with steady flows that can be considered quasi 1-D. For **steady 1D flow**, the left-hand side is:
>
> $
> \oint \rho \left( u + \frac{p}{\rho} + \frac{V^2}{2} + gz \right)\,\vec{V}\cdot\vec{n}\,dA
> $
>
> This term can only be non-zero if $\vec{V}\cdot\vec{n} \neq 0$. Basically, the fluid has to be crossing that particular surface area. If we assume a quasi 1D flow where properties are considered constant within the entrance and exit areas of the flow, then:
>
> $
> \oint \rho \left( u + \frac{p}{\rho} + \frac{V^2}{2} + gz \right)\,\vec{V}\cdot\vec{n}\,dA
> $
>
> $
> =
> \sum_{flow\ out}
> \left(
> u + \frac{p}{\rho} + \frac{V^2}{2} + gz
> \right)\dot{m}
> -
> \sum_{flow\ in}
> \left(
> u + \frac{p}{\rho} + \frac{V^2}{2} + gz
> \right)\dot{m}
> $
![[ME 308 - Exam 1 Notes#^3433fe]]
- In the full energy equation above, you need to include the $\rho u_{rel}\cdot dA$ term if the flow is non-uniform across the in/outlet area, for example if velocity varies with position. If flow is treated as 1D & uniform over each section, the integral simplifies to $\dot{m}\left( u+\frac{p}{\rho}+\frac{V^2}{2}+gz \right)$
- If there's no pump/turbine/shaft,... device doing work on the water between 2 points, $\dot{W}=0$
- If there's no pressure/temperature change, $\Delta u\approx 0$
- Can neglect pressure term sometimes in $F_{B}$ if there's no pressure change across the CV
- If exposed to atmospheric pressure, use gauge pressure s.t there's no pressure change within the CV
- If mass is accumulating within the CV then $\frac{d}{dt}\int_{CV}\rho dV\neq0$
- If fluid is leaving a moving CV, $\dot{m}=-\rho Av$ rather than $-\rho A(v-u);$ same applies to LME
>[!info] Where to start on problems
>1. **Start with COM** when mass flow/accumulation matters *(tank filling/draining, changing mass, multiple in/outlets, unknown $\dot{m}$)*
>$
> \frac{d}{dt} \int_{CV} \rho dV+\int_{CS}\rho \vec{V}_{rel}\cdot d\vec{A}=0
>$
>2. **Start with LME** when problem asks for for force, acceleration, reaction force, or momentum change *(jet hitting vane/cart, nozzle force, bend force, hydraulic jump)*
>$
> \sum \vec{F}=\text{ momentum accumulation }+ \text{ momentum flux}
>$
>3. **Start with energy** when the unknown is pressure, velocity, elevation, pump/turbine work, or head *(siphon, nozzle velocity, pressure difference, height change, Bernoulli-type setup)*
>$
> \frac{p}{\rho}+\frac{V^2}{2}+gz=\dots
>$
- Force $F_{R}=p_{c}A$ acts through the center of pressure, $p_{c}$ is calculated using the centroid depth below free surface
- Center of pressure $y'=y_{c}+\frac{I_{xc}}{Ay_{c}}$ where $y_{c}$ is the centroid depth below the free surface
- For $\frac{d}{dt}$ term to be included in the LME, relative LM stored in the CV must accumulate, i.e. mass flow rate
- If the CS is not moving, then $u_{rel}=u_{fluid}~(u_{xyz}=u_{XYZ})$, so the relative velocity is just the fluid velocity as it crosses the CS. Otherwise, $u_{xyz}$ and $u_{rel}$ are diff. quantities
- For curved surfaces, $F_{V}=\rho gV_{eff}$ where $V$ is the imaginary fluid volume above the wetted curved surface up to the free surface ([[ME 308 HW 02 Solutions#ME 308 HW 02.pdf page=5 Problem 5|HW 02 p5]])
- Horizontal force on curved surface $F_{H}=p_{C}A_{proj}$ where $A_{proj}$ the projected area of the curved surface onto a flat plane perpendicular to the force direction
- Easier to consider the surfaces as shapes you're subtracting from kind of
- For hydrostatic force and center of pressure, only consider the body's submerged area (see [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=149&selection=271,0,271,3|4.59]])
## Engineering Fluid Mechanics
### [[Engineering Fluid Mechanics - Roberson, Crowe.pdf#page=192|The Control Volume Approach]]
$B$ represents general extensive property and $\beta$ be the symbol for corresponding intensive property
$
B=\int\beta dm=\int\beta \rho dV
$
$
\text{Flow rate out - flow rate in }=u_{2}A_{2}-u_{1}A_{1}=\vec{u}_{2}\cdot \vec{A}_{2}+\vec{u}_{1}\vec{A}_{1}=\sum_{cs}\vec{u}\cdot \vec{A}
$
$
\dot{m}=\sum_{cs}\rho \vec{u}\cdot A
$
$
\dot{B}=\int_{cs}\beta \rho \vec{u}\cdot d\vec{A}
$
$
\text{Well-defined, discrete in/outlets: } \frac{dB_{sys}}{dt}=\frac{d}{dt} \int_{CV}\beta \rho dV+\sum_{CS}\beta \rho \vec{u}\cdot A
$
$
\text{When velocity is variable across a section, }\frac{dB_{sys}}{dt}=\frac{d}{dt} \int_{CV}\beta \rho dV+\int _{CS} \beta \rho \vec{u} \cdot d\vec{A}
$
### [[Engineering Fluid Mechanics - Roberson, Crowe.pdf#page=224|Momentum Equation]]
$ \int_{CS}\vec{V}_{xyz}\rho \vec{V}_{xyz}\cdot d\vec{A}+\frac{d}{dt} \int_{CV}\vec{V}_{xyz}\rho dV=\vec{F}_{S}+\vec{F}_{B}-\int_{CV}\vec{a}_{rf}\rho dV$
First term (on the left) is the net flow of momentum out of the control volume. Therefore, if the flow through the control volume is uniform $\Delta MV=0$, the flow of momentum entering the CV is the same as the flow of momentum leaving the CV $\therefore$ this term will be zero
If flow is nonuniform, change in the flow of momentum will exist between in/outflow sections, and magnitude of the term must be evaluated (common applications include flow in bends & thru nozzles)
Control surface is chosen s.t the unknown(s) you're seeking in the solution are isolated by your choice
There are two different velocity values used in the term on the left. The first is the velocity carried w/ momentum and the second is velocity thru the control surface, used for $\dot{m}$. To calculate $F_{x},$ you'd use the term
$
\sum F_{x}=\frac{d}{dt} \int_{CS}V_{x}(\rho V\cdot dA)+\sum_{CS} v_{x} \rho V\cdot A
$
**See Examples 6.2, 6.7**
### [[Engineering Fluid Mechanics - Roberson, Crowe.pdf#page=268|The Energy Equation]]
From eqn. sheet we have the form of the energy equation
$
\frac{d}{dt}\int_{CV} e\rho dV+\int_{CS}\left( h+\frac{1}{2}U^2+gz \right)(\rho u_{rel}\cdot dA)=\dot{Q}_{\text{into CV}}+\dot{W}_{\text{out of CV}}
$
^3433fe
where $e=u+\frac{1}{2}U^2+gz,h=u+\frac{p}{\rho}$ ($h$ is specific enthalpy)
Flow work is the work done by pressure forces as the system moves thru the space
$
\Delta W_{f_{2}}=U_{2}p_{2}A_{2}\Delta t\to\dot{W}_{f_{2}}=U_{2}p_{2}A_{2}
$
$
\dot{W}_{f}=\sum_{CS} \frac{p}{\rho}\rho \vec{U}\cdot \vec{A}
$
Shaft work is defined as nay work other than flow work - usually the form of work done through a shaft that takes energy in/out of system
Basic form of energy equation:
$
\dot{Q}-\dot{W}_{s}-\sum_{CS} \frac{p}{\rho}\rho \vec{U}\cdot \vec{A}=\frac{d}{dt} \int_{CV}\left( \frac{U^2}{2} +gz+u\right)\rho dV+\sum_{CS}\left( \frac{U^2}{2}+gz+u \right)\rho \vec{U}\cdot \vec{A}
$
More general form of energy equation:
$
\dot{Q}-\dot{W}_{s}=\frac{d}{dt} \int_{CV} \left( \frac{U^2}{2}+gz+u \right)\rho dV+\int_{CS}\left( \frac{p}{\rho}+\frac{V^2}{2}+gz+u \right)
$
See p. 278,
## [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=125|Introduction to Fluid Mechanics - Momentum Eqn. for Inertial CV]]
For inertial CV:
$
\sum F_{x}=\frac{d}{dt} \int_{CS}V_{x}(\rho V\cdot dA)+\sum_{CS} v_{x} \rho V\cdot A
$
Assuming steady state:
$
\sum F_{x}=\sum_{CS}v_{x}\rho V\cdot A=\dot{m}(V_{2}'-V_{1}')=\rho AV'(V_{2}'-V_{1}')
$
For non-inertial reference frames, the eqns. above will not work -> must derive momentum eqn. for linearly accelerating CV. Inertial reference frame is denoted by $XYZ$
$
\vec{P}_{sys}=\int_{M(\text{system})}\vec{u}dm=\int_{CV(\text{system})}\vec{u}\rho dV, \vec{F}= \frac{d\vec{P}}{dt}\Biggr)_{\text{system}}
$
$
\vec{F}=\frac{d\vec{P}_{XYZ}}{dt}=\frac{d}{dt}\int_{M\text{(system)}}\vec{u}_{XYZ}dm=\int_{M\text{(system)}} \frac{d\vec{u}_{xyz}}{dt}dm
$
$
\vec{u}_{XYZ}=\vec{u}_{xyz}+\vec{u}_{rf}
$
$
\frac{d\vec{u}_{XYZ}}{dt}=\vec{a}_{XYZ}=\frac{d\vec{u}_{xyz}}{dt}+\frac{d\vec{u}_{rf}}{dt}=\vec{a}_{xyz}+\vec{a}_{rf}
$
- $\vec{a}_{XYZ}$ is rectilinear acceleration relative to the inertial reference frame $XYZ$
- $\vec{a}_{xyz}$ is the rectilinear acceleration of the system relative to the noninitial reference frame $xyz$
- $\vec{a}_{rf}$ is the rectilinear acceleration of the noninitial reference frame $xyz$ (i.e. of the control volume relative to the inertial frame $XYZ$)
$
\vec{F}=\int_{M\text{(system)}}\vec{a}_{rf}dm+\int_{M\text{(system)}} \frac{d\vec{u}_{xyz}}{dt}dm
$
where the linear momentum of the system is given by
$
\vec{P}_{xyz})_{\text{system}}=\int_{M\text{(system)}}\vec{u}_{XYZ}dm=\int_{V\text{(system)}}\vec{u}_{xyz}\rho dV
$
$
\vec{F}-\int_{CV}\vec{a}_{rf}\rho dV=\frac{ \partial }{ \partial t } \int_{CV}\vec{u}_{xyz}\rho dV+\int_{CS}\vec{u}_{xyz}\rho \vec{u}_{xyz}\cdot d\vec{A}
$
$
\boxed{ \vec{F}_{S}+\vec{F}_{B}-\int_{CV}\vec{a}_{rf}\rho dV=\frac{ \partial }{ \partial t } \int_{CV} \vec{u}_{xyz}\rho dV+\int_{CS}\vec{u}_{xyz}\rho \vec{u}_{xyz}\cdot d\vec{A} }
$
**See Examples [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=125&selection=187,0,192,1|4.10]], [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=129&selection=313,0,313,4|4.11]]**
# Textbook Practice Problems
| Problem | Priority | Topics Combined | Length | Why It Fits Your Exam |
| ---------------------------------------------------------------------- | -------: | ------------------------------------------------------ | ----------: | ------------------------------------------------------------------------------------------------------------------------------------------------------------------------ |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=153\|4.91]] | ★★★ | Bernoulli + LME + Hydrostatic Force | Medium | Probably the closest match to what you're asking for. Use energy/Bernoulli to get the jet behavior, momentum for the jet force, and hydrostatics on the plate/tank side. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=153\|4.94]] | ★★★ | Manometer + Bernoulli + LME | Medium | Stagnation tube/manometer gives jet velocity, then use momentum to find force on the curved vane. Very realistic exam-style multi-step problem. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=256\|6.52]] | ★★★ | COM + Bernoulli + LME | Medium | Find the pipe pressure using Bernoulli, then use that pressure and momentum flux to find the nozzle/flange force. Excellent combined problem. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=256\|6.51]] | ★★★ | COM + Bernoulli + LME | Medium | Reverse version of 6.52: flange force is given, and you need to combine Bernoulli and momentum to solve for flow rate. More challenging algebraically. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=150\|4.67]] | ★★★ | Pump Head / Energy + COM + LME | Medium–Long | Pump adds head, flow changes diameter and direction, then momentum gives the force on the whole assembly. Good comprehensive CV problem. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=153\|4.92]] | ★★★ | Bernoulli + Free Jet + LME / Stagnation Pressure | Medium | First determine jet speed from rise height, then analyze the force/pressure when the jet is stopped by a hand or window. Several concepts without weird geometry. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=151\|4.73]] | ★★★ | Hydrostatic Pressure + COM + LME | Medium | Open-channel flow is redirected by a gate. Requires handling hydrostatic pressure at the inlet and momentum change through the gate. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=151\|4.69]] | ★★★ | Hydrostatic Pressure + COM + LME | Medium–Long | Sluice-gate style problem with pressure forces and momentum flux. Strong practice for recognizing when pressure on a CS is hydrostatic rather than uniform. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=153\|4.93]] | ★★ | Bernoulli + LME + Force Equilibrium | Medium | Jet slows as it rises, then supports a disk. Requires finding $V(h)$ and balancing jet momentum force against weight. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=257\|6.57]] | ★★ | Bernoulli + Moving Surface + Stagnation Pressure + LME | Medium–Long | Jet strikes a downward-moving object. Good integration of energy and momentum, but slightly more involved than I'd expect for a normal exam problem. |
| [[Introduction to Fluid Mechanics - Fox, McDonald.pdf#page=257\|6.62]] | ★★ | Bernoulli + COM + LME | Medium | Flow around a body at a pipe outlet. Requires pressure from Bernoulli and then force from momentum. Straight geometry. |
![[ME 308 - Exam 1 Assumptions]]