### Problem 1
| Part | Final Answer |
|---|---|
| (a) | $\dfrac{\theta}{\delta}=\int_0^1\left(r^{1/7}-r^{2/7}\right)dr=\dfrac{7}{72}\approx0.09722$. |
| (b) | $\theta(x)=\left[\dfrac54(0.0233)\left(\dfrac7{72}\right)^{1/4}U^{3/4}\nu^{1/4}x\right]^{4/5}=0.03707\,xRe_x^{-1/5}$, where $Re_x=Ux/\nu$. |
| (c), scoop at $L=1.45\text{ m}$ | $Re_L=4.304\times10^6$, $\theta(L)=2.533\text{ mm}$, $\delta(L)=\dfrac{72}{7}\theta(L)=26.05\text{ mm}$. |
| (d), profiles | See the completed table and plot below. At a given $y/\delta$ within the layer, the turbulent profile has a larger $u/U$; its fuller profile reflects stronger momentum mixing toward the wall. |
For the laminar column, use $\delta_{99}\approx5\sqrt{\nu x/U}$, so $\eta=5y/\delta$, and read $f'(\eta)$ from the supplied Blasius table. For the turbulent column, use $u/U=(y/\delta)^{1/7}$.
| $y/\delta$ | 0 | 0.2 | 0.4 | 0.6 | 0.8 | 1.0 |
|---|---:|---:|---:|---:|---:|---:|
| $\eta$ (Blasius) | 0 | 1 | 2 | 3 | 4 | 5 |
| $u/U$ (laminar) | 0 | 0.3298 | 0.6298 | 0.8460 | 0.9555 | 0.9915 |
| $u/U$ (turbulent) | 0 | 0.7946 | 0.8773 | 0.9296 | 0.9686 | 1.0000 |
![[ME 308 Boundary Layer Velocity Profiles (7th power).png]]
### Problem 2
The transition length from each local leading edge is $x_{tr}=Re_{x,tr}\nu/V=0.375\text{ m}$. The local chord varies linearly from $c_r=1.5\text{ m}$ at midspan to $c_t=0.5\text{ m}$ at either tip.
| Part | Final Answer |
|---|---|
| (a) | Laminar area per face $=bx_{tr}=1.125\text{ m}^2$; total area per face $=b(c_r+c_t)/2=3.000\text{ m}^2$. **Laminar fraction $=37.5\%$.** |
| (b) | Using $\bar C_{f,\mathrm{lam}}=1.328/\sqrt{Re_{x,tr}}$, the friction force on both laminar faces is $F_{\mathrm{lam}}=2(\tfrac12\rho V^2)(bx_{tr})\bar C_{f,\mathrm{lam}}=\mathbf{1.014\text{ N}}$. |
| (c) | Using the table's local turbulent relation $C_{f,x}=0.0594Re_x^{-1/5}$ downstream of transition and integrating over the varying local chord, $F_{\mathrm{turb}}=2(\tfrac12\rho V^2)b(0.07425)(\nu/V)^{1/5}\left[\dfrac{c_r^{9/5}-c_t^{9/5}}{(9/5)(c_r-c_t)}-x_{tr}^{4/5}\right]=\mathbf{3.419\text{ N}}$. |
### Problem 3
Let $A=\pi D^2/4$ be the projected area of either original cup. View the diagram with the wind blowing to the right.
| Part | Final Answer |
|---|---|
| (a), drag | $F_1=\tfrac12\rho V^2A C_{D,1}$ on the upper cup; $F_2=\tfrac12\rho V^2A C_{D,2}$ on the lower cup. Both forces act downwind. |
| (a), torque and direction | $M_{\mathrm{net}}=R(F_1-F_2)=\tfrac12\rho V^2AR(C_{D,1}-C_{D,2})$ **clockwise** in the diagram. |
| (b) | Enlarge the lower, lower-drag cup and keep the upper cup at diameter $D$: $C_{D,2}k^2=C_{D,1}$, hence $\boxed{k=\sqrt{C_{D,1}/C_{D,2}}}$. |
### Problem 4
Set $\xi=x/c$ and $f(\xi)=1+2\xi-\tfrac32\xi^2$.
| Part | Final Answer |
|---|---|
| (a) | From inviscid outer-flow momentum, $\displaystyle\frac{dp}{dx}=-\rho u_e\frac{du_e}{dx}=-\frac{\rho U_\infty^2}{c}\left(1+2\xi-\frac32\xi^2\right)(2-3\xi)$. |
| (b) | **Favorable** ($dp/dx<0$): $0\le x/c<2/3$. **Zero gradient**: $x/c=2/3$. **Adverse** ($dp/dx>0$): $2/3<x/c\le1$. |
### Problem 5
| Part | Final Answer |
|---|---|
| (a), forces | Free-body diagram: weight $mg$ downward; buoyancy $F_B=\rho g\pi D^3/6$ and drag $F_D=\tfrac12\rho V_t^2 C_D\pi D^2/4$ upward. At terminal speed, $mg=F_B+F_D$. |
| (a), mass | $Re_D=V_tD/\nu=1.00\times10^5$. Reading the supplied graph gives $C_D\approx0.45$–$0.50$ (about $0.47$). Thus $m=\rho\pi D^3/6+F_D/g\approx\mathbf{0.71\text{ kg}}$ (roughly $0.70$–$0.72\text{ kg}$, depending on the graph reading). |
| (b) | From the supplied pressure plot, separation occurs at about **$75^\circ$ for laminar** and **$140^\circ$ for turbulent** flow, measured from the front stagnation point. Later separation narrows the low-pressure wake and reduces pressure drag. |
| (c) | **Decrease the mass.** With $V_t$ and $D$ fixed, a lower $C_D$ lowers upward drag, so a smaller weight is needed to balance drag plus buoyancy. |