| Asked for | Approach |
| --- | --- |
| Reactions, $V(x)$, $M(x)$ | FBD → equilibrium; add compatibility if indeterminate |
| Full deflection function | Find piecewise $M(x)$ → integrate $EI v''=M$ twice |
| Reactions using tables | Release redundant → superpose load and redundant effects → compatibility |
| One displacement/rotation; frames or rods | Castigliano: sum relevant member energies → differentiate |
| Maximum stress/design size | Find critical $M,V$ → section properties → check bending **and** shear |
# Cross-section and stresses
![[Pasted image 20261004174311.png|right|200]]For a homogeneous section, the neutral axis passes through its centroid:
$
\bar y=\frac{\sum A_i y_i}{\sum A_i},\qquad
I=\sum\left(I_{c,i}+A_i d_i^2\right)
$
$
I_{\rm rectangle}=\frac{bh^3}{12},\qquad
I_{\rm circle}=\frac{\pi r^4}{4},\qquad
I_{\rm annulus}=\frac{\pi(r_o^4-r_i^4)}4
$
$
\boxed{\sigma_x=-\frac{My}{I}},\qquad
\boxed{\tau=\frac{VQ}{It}},\qquad
Q=A^*\bar y^*
$
- $y,\bar y^*$ are measured from the **neutral axis**; $I$ uses the **whole section**. $A^*$ is the portion above/below the evaluation cut; $t$ is the local width there.
- Bending stress is linear in $y$; positive $M$ compresses the top. For asymmetric sections, check top/bottom distances and both moment signs for maximum tension/compression.
- Shear is zero at the top/bottom free surfaces; its maximum is often near the neutral axis. At a flange/web width change, check both sides using their respective $t$.
- On a stress element, show tension outward/compression inward; complementary shears are equal, with opposite arrows on opposite faces.
$
\tau_{\max,\rm rectangle}=\frac{3|V|}{2A},\qquad
\tau_{\max,\rm solid\ circle}=\frac{4|V|}{3A}
$
# Deflection by integration
$
\boxed{M=EI v''},\qquad \theta=v',\qquad
V=(EI v'')',\qquad w=(EI v'')''
$
![[ME 323 Lec 17, 19 - Beam Deflections#^e4fdde]]
| Location | Conditions |
| --- | --- |
| Fixed end | $v=0,\ \theta=0$ |
| Pin/roller at a beam endpoint | $v=0$; $M=0$ if no applied end couple |
| Interior roller under continuous beam | $v=0$; $\theta$ continuous; **$M$ need not vanish** |
| Unloaded free end | $M=0,\ V=0$; $v,\theta$ generally nonzero |
| Ordinary segment junction | $v^-=v^+,\ \theta^-=\theta^+$ |
# Superposition and compatibility
- Applies to linear elastic behavior with small deflections. Match table supports, origin, load direction, and piecewise interval.
- Remove redundant $R$ to leave a stable determinate beam. At its former support:
$
\boxed{v_{\rm loads}(a)+R f_{aa}=v_{\rm prescribed}(a)}
$
- $f_{aa}$ is displacement at $a$ from a unit force there. For a stationary rigid support, the right side is zero. Solve $R$, then recover other reactions by equilibrium.
- For an elastic rod support, beam motion must match the rod's signed extension $NL/(EA)$, not zero. Include rod energy if using Castigliano.
- Partial distributed loads can be built by adding/subtracting table cases. Beyond a load-free, zero-moment segment, extend using $v(x)=v(a)+\theta(a)(x-a)$.
# Energy and Castigliano
For gradually applied loads on a linear elastic body:
$
W_{\rm ext}=U=\frac12\sum_i(P_i\delta_i+M_i\theta_i+T_i\phi_i)
$
$
\boxed{U=\sum_{\rm members/segments}\int
\left(\frac{N^2}{2EA}+\frac{M^2}{2EI}+\frac{T^2}{2GJ}+\frac{f_sV^2}{2GA}\right)dx}
$
$f_s=6/5$ for a rectangle, $10/9$ for a solid circle. $J$ is the polar moment for circular-shaft torsion; $I$ is for bending. Select modes from each member's **local** $N,V,M,T$; “neglect shear energy” does not remove axial or torsional energy.
$
\delta_i=\frac{\partial U}{\partial P_i},\qquad
\theta_i=\frac{\partial U}{\partial M_i},\qquad
\phi_i=\frac{\partial U}{\partial T_i}
$
For bending alone:
$
\delta_P=\sum\int\frac{M}{EI}\frac{\partial M}{\partial P}\,dx
$
1. Release independent redundants; express reactions/internal resultants in terms of them and the applied loads.
2. Sum energy over **every relevant segment**, using its own stiffness.
3. For a stationary rigid restraint: $\partial U/\partial R_i=0$. Solve redundants, then equilibrium.
4. For an unloaded displacement/rotation location, introduce a **dummy force/moment in the desired direction** before finding reactions/resultants. Differentiate, **then set it to zero**.
Hold other independent loads/redundants fixed during partial differentiation; substitute solved redundant values afterward. A negative displacement opposes the assumed load direction. $U=\tfrac12P\delta$ alone cannot isolate several displacements under multiple loads.
# Fast conceptual checks
- Same geometry and prescribed loads on a **determinate** beam: changing $E$ changes deflection, not $M,V$ or stresses. Relative stiffness can change indeterminate reactions.
- Fixed loading pattern: $v\propto1/(EI)$. Circular $I\propto D^4$: doubling $D$ divides deflection by $16$.
- Cantilever tip force: $v_{\rm tip}=PL^3/(3EI)$ in magnitude; doubling $L$ gives $8v$. Uniform load: deflection scales as $wL^4/(EI)$.
- For unchanged internal forces, energy decreases as stiffness increases and scales with load squared. Energy is nonnegative even when displacement is negative.
- Keep units consistent: $M$ in N·mm with $I$ in mm$^4$ gives stress in MPa; $U$ has force × length units; slopes are radians.